Magma PCI Expansion System PE6R4 Manual de usuario descargar pdf (Pagina 16)

Pro Tools and Pro Tools HD 10.0 on Mac OS X 10.6.x (“Snow Leopard”) and Mac OS X 10.7.x (“Lion”) — 10/13/11 16

Known Issues with Audio Interfaces

HD OMNI

Noise in the Output Signal from HD OMNI with Digital Input (PTSW-1614)

If HD OMNI is connected to a digital source with a mismatched clock and Sample Rate Conversion (SRC) is not enabled, you will

hear noise (including loud “pops”) in the output signal. To correct this problem, either enable SRC or ensure that the clock of the

digital source and HD OMNI are matched correctly.

HD OMNI Front Panel SETUP Menus are Unresponsive after Pro Tools Quits Unexpectedly (PTSW-125692)

HD OMNI will not automatically recover “stand-alone” mode if Pro Tools quits unexpectedly (or if you disconnect the DigiLink

cable from HD OMNI while Pro Tools is running). As a result, some of the SETUP functions accessible from the front panel will

be unavailable. Power cycle HD OMNI to recover stand-alone mode.

Graphic Redraw Problems in the Hardware Setup Dialog (PTSW-122690, PTSW-1346, and PTSW-1235)

When changing the Hardware Setup configuration for HD OMNI, it is possible to encounter graphics redraw problems in some

cases. To force a graphics redraw of the Hardware Setup dialog, close and reopen the Hardware Setup dialog.

Versions of Pro Tools Lower than 8.1 Quit on Launch with HD OMNI (PTSW-1976)

When launching versions of Pro Tools lower than 8.1 with HD OMNI connected and powered on, Pro Tools quits when initializing

DSI. To avoid the problem, power off HD OMNI before launching versions of Pro Tools lower than 8.1.

No Sound on Output after Hardware RESET (PTSW-126575)

After resetting the HD OMNI interface to the default factory settings using the front panel controls, the HD OMNI interface stops

emitting sound in sessions where the outputs are not assigned to the Monitor output path. To correct this problem, press the ALT

monitor button to switch to the ALT Monitor path, and then press it again to switch back to the Main Monitor path.

Loss of Monitor Path when Launching Pro Tools with HD OMNI Off or Disconnected (PTSW-127313)

When launching Pro Tools and opening I/O Setup after powering off HD OMNI or disconnecting it from the system, the inactive

Monitor path is not present in Output tab. You may need to restore the default I/O Settings and remap the corresponding Output

Busses.

Output Paths are not Automatically Created in the Output Page of the I/O Setup After Disabling the Corresponding Monitor Path

in the Monitor Page of the Hardware Setup and Re-assigning the Outputs from “None” to Physical Outputs in the Main Page of

the Hardware Setup (PTSW-127559)

After disabling the Monitor path in the Monitor page of the Hardware Setup and re-assigning the corresponding Outputs from

“None” to physical outputs (such as “A 1-2”) in the Main Page of the Hardware Setup, these Output paths are not automatically

created in the Output Page of the I/O Setup. You will have to manually create the appropriate Output paths in the I/O Setup (or

click Default).

Changing Monitor Path Output Assignments in the Hardware Setup does not Update the Output Paths in the Output Page of the

I/O Setup (PTSW-127563)

When changing Monitor path Output assignments in the Monitor page of the Hardware Setup (such as setting the Monitor path

Format to None or assigning the Monitor to different physical outputs), the Output paths in the Output page of the I/O Setup do

not reflect the corresponding changes. You will have to manually create the appropriate Output paths in the I/O Setup (or click

Default).

When Creating New Sessions, Using the I/O Settings Selector Can Result in Unexpected Output Assignments if HD OMNI Has

an Assigned Monitor Path (PTSW-123896)

If HD OMNI has an assigned Monitor path, Output paths created by the selected I/O Settings option in the New Session dialog may

be offset by the channel width of the Monitor path. If this happens, you will have to manually create the appropriate Output paths

in the I/O Setup (or click Default).

1 2 ... 11 12 13 14 15 16 17 18 19

Sin comentarios

Magma PCI Expansion System PE6R4 Manual de usuario Pagina 16